4.1 Installation
(1) Place your Netphone-ML210A near a power source.
(2) Plug the RJ-45 connector of the Ethernet 10/100Base-T cable into the Netphone-ML210A's side input port"(1)",and plug the other side into a hub or switch, or wall/ground socket of the structuring cable.
(3) Plug the accessory power-adapter into the power outlet, then connect the output-plug to power-port "(3)" of the Netphone-ML210A.
NOTE: If the network is without a HUB, the Netphone-ML210A should be connected with other Ethernet equipment (such as XDSL adapter, CABLE modem or PC) by crossing-over cable. Otherwise the direct-connecting cable is applied.
4.2 Settings
4.2.1Setting Steps
If your Netphone account has been set up, please skip the section '5.2.5 Account settings'.
4.2.2 Dynamic IP Users
If you need to configure DNS IP
Press SET/OK to enter the submenu and select 'DNS1' by pressing UP and DOWN.
Press SET/OK to enter setting menu and configure your DNS2.
If a spare DNS is requested, press SET/OK to enter the submenu and select DNS2 by pressing UP and DOWN; or you may press SET/OK to enter setting menu and configure your DNS2.
If the account information has been set up, you may start using as soon as you plug in.
4.2.3 PPPoE Users' Parameter Settings
Press 'SET/OK' to enter the main menu, and use 'UP' and 'DOWN' to scroll and select 'TCP/IP Settings'.
A. Do not use DHCP
Press 'SET/OK' to enter the submenu, and use 'UP' and 'DOWN' to select 'Use DHCP'.
Press 'SET/OK' to enter settings. Input 0 to disable DHCP.
B. Use PPPoE
Press 'SET/OK' to enter the submenu, and use 'UP' and 'DOWN' to select 'Use PPPoE'.
Press 'SET/OK' to enter settings. Input 1 to enable PPPoE.
C. Set PPPoE account
Press 'SET/OK' to enter the submenu, and use 'UP' and 'DOWN' to select 'PPP Identity'.
Press 'SET/OK' to enter settings. Continue pressing a number key to change the letter, and press the '#' key to confirm it.
D. Set PPPoE Password
Press 'SET/OK' to enter the submenu, and use 'UP' and 'DOWN' to select 'PPP Identity'.
Press 'SET/OK' to enter settings. Continue pressing a number key to change the letter, and press the '#' key to confirm it.
E. If DNS IP is requested
Press 'SET/OK' to enter the submenu, and use 'UP' and 'DOWN' to select 'DNS1'.
Press 'SET/OK' to enter settings and configure your 'DNS1'.
If a spare DNS is requested, press SET/OK to enter the submenu and select DNS2 by pressing UP and DOWN; or you may press SET/OK to enter setting menu and configure your DNS2.
NOTE: When you finish setting up, press 'SET/OK' to confirm or 'ESC' to cancel. If you input your setting accordingly, the LCD will display the new setting. Otherwise, the LCD will display 'Input Invalid'; press ESC to return to your previous setting.
4.2.4 Static IP Users' Parameter Settings
Press 'SET/OK' to enter the main menu, and use 'UP' and 'DOWN' to scroll and select 'TCP/IP Settings'.
A. Do not use DHCP
Press 'SET/OK' to enter the submenu, and use 'UP' and 'DOWN' to select 'Use DHCP'.
Press 'SET/OK' to enter settings. Input 0 to disable DHCP.
B. Set Local IP
Press 'SET/OK' to enter the submenu, and use 'UP' and 'DOWN' to select 'Local IP'.
Press 'SET/OK' to enter settings. Input the IP address. Use the '*' key for the dot.
C. Set subnet mask
Press 'SET/OK' to enter the submenu, and use 'UP' and 'DOWN' to select 'Subnet Mask'.
Press 'SET/OK' to enter settings. Input the IP address. Use the '*' key for the dot.
D. Set Router IP
Press 'SET/OK' to enter the submenu, and use 'UP' and 'DOWN' to select 'Router IP'.
Press 'SET/OK' to enter settings. Input the IP address. Use '*' key for the dot.
E. Set DNS IP
Press 'SET/OK' to enter the submenu, and use 'UP' and 'DOWN' to select DNS IP.
Press 'SET/OK' to enter settings. Input the IP address. Use '*' key for the dot.
If a spare DNS is requested, press SET/OK to enter the submenu and select DNS2 by pressing UP and DOWN; or you may press SET/OK to enter setting menu and configure your DNS2.
NOTE: When you finish set- up, press 'SET/OK' to confirm or 'ESC' to cancel. If you input your setting accordingly, the LCD will display the new setting. Otherwise, the LCD will display 'Input Invalid'; press ESC to return to your previous setting.
4.2.5 Account Settings
Press 'SET/OK' to the main menu, use 'UP' and 'DOWN' to select 'Account Settings.
A. Set phone number
Press 'SET/OK' to the submenu, use 'UP' and 'DOWN' to select 'Phone Number'.
Press 'SET/OK', and then, use 0~9 to input the phone number
B. Set user ID
Press 'SET/OK' to the submenu, use 'UP' and 'DOWN' to select 'User Identity'.
Press 'SET/OK', and then, use 0~9 to input the user ID. Continuous press a number key to change the letter and press '#' key to confirm it.
C. Set user password
Press 'SET/OK' to the submenu, use 'UP' and 'DOWN' to select 'User Password'.
Press 'SET/OK', and then, use 0~9 to input the user password. Continuous press a number key to change the letter and press '#' key to confirm it. |
