|
|
|
| Home > Support > Broadband Installation |
 |
Broadband phone Installation and Configuration |
|
|
| Installation |
| (1) |
Place your broadband phone products near a power source. |
| (2) |
Plug the RJ-45 connector of the Ethernet 10/100Base-T cable into the broadband phone products side input port"(1)",and plug the other side into a hub or switch, or wall/ground socket of the structuring cable. |
| (3) |
Plug the accessory power-adapter into the power outlet, then connect the output-plug to power-port "(3)" of the Netphone-KE products. |
|
| NOTE: If the network is without a HUB, the broadband products should be connected with other Ethernet equipment (such as XDSL adapter, CABLE modem or PC) by crossing-over cable. Otherwise the direct-connecting cable is applied.
|
| Settings |
| 1) |
Setting Steps
If your MeritCall account has been set up before hand please skips the section '5.2.5 Account settings'.
|
| 2) |
Dynamic IP Users
If you need to configure DNS IP
Press SET/OK to enter the submenu and select 'DNS1' by pressing UP and DOWN.
Press SET/OK to enter setting menu and configure your DNS2.
If a spare DNS is requested, press SET/OK to enter the submenu and select DNS2 by pressing UP and DOWN; or you may press SET/OK to enter setting menu and configure your DNS2.
If the account information has been set up, you may start using as soon as you plug in.
|
| 3) |
PPPoE Users' Parameter Settings
Press 'SET/OK' to enter the main menu, and use 'UP' and 'DOWN' to scroll and select 'TCP/IP Settings'.
A. Do not use DHCP
Press 'SET/OK' to enter the submenu, and use 'UP' and 'DOWN' to select 'Use DHCP'.
Press 'SET/OK' to enter settings. Input 0 to disable DHCP.
B. Use PPPoE
Press 'SET/OK' to enter the submenu, and use 'UP' and 'DOWN' to select 'Use PPPoE'.
Press 'SET/OK' to enter settings. Input 1 to enable PPPoE.
C. Set PPPoE account
Press 'SET/OK' to enter the submenu, and use 'UP' and 'DOWN' to select 'PPP Identity'.
Press 'SET/OK' to enter settings. Continue pressing a number key to change the letter, and press the '#' key to confirm it.
D. Set PPPoE Password
Press 'SET/OK' to enter the submenu, and use 'UP' and 'DOWN' to select 'PPP Identity'.
Press 'SET/OK' to enter settings. Continue pressing a number key to change the letter, and press the '#' key to confirm it.
E. If DNS IP is requested
Press 'SET/OK' to enter the submenu, and use 'UP' and 'DOWN' to select 'DNS1'.
Press 'SET/OK' to enter settings and configure your 'DNS1'.
If a spare DNS is requested, press SET/OK to enter the submenu and select DNS2 by pressing UP and DOWN; or you may press SET/OK to enter setting menu and configure your DNS2.
NOTE: When you finish setting up, press 'SET/OK' to confirm or 'ESC' to cancel. If you input your setting accordingly, the LCD will display the new setting. Otherwise, the LCD will display 'Input Invalid'; press ESC to return to your previous setting.
|
| 4) |
Static IP Users' Parameter Settings
Press 'SET/OK' to enter the main menu, and use 'UP' and 'DOWN' to scroll and select 'TCP/IP Settings'.
A. Do not use DHCP
Press 'SET/OK' to enter the submenu, and use 'UP' and 'DOWN' to select 'Use DHCP'.
Press 'SET/OK' to enter settings. Input 0 to disable DHCP.
B. Set Local IP
Press 'SET/OK' to enter the submenu, and use 'UP' and 'DOWN' to select 'Local IP'.
Press 'SET/OK' to enter settings. Input the IP address. Use the '*' key for the dot.
C. Set subnet mask
Press 'SET/OK' to enter the submenu, and use 'UP' and 'DOWN' to select 'Subnet Mask'.
Press 'SET/OK' to enter settings. Input the IP address. Use the '*' key for the dot.
D. Set Router IP
Press 'SET/OK' to enter the submenu, and use 'UP' and 'DOWN' to select 'Router IP'.
Press 'SET/OK' to enter settings. Input the IP address. Use '*' key for the dot.
E. Set DNS IP
Press 'SET/OK' to enter the submenu, and use 'UP' and 'DOWN' to select DNS IP.
Press 'SET/OK' to enter settings. Input the IP address. Use '*' key for the dot.
If a spare DNS is requested, press SET/OK to enter the submenu and select DNS2 by pressing UP and DOWN; or you may press SET/OK to enter setting menu and configure your DNS2.
NOTE: When you finish set- up, press 'SET/OK' to confirm or 'ESC' to cancel. If you input your setting accordingly, the LCD will display the new setting. Otherwise, the LCD will display 'Input Invalid'; press ESC to return to your previous setting.
|
| 5) |
Account Settings
Press 'SET/OK' to the main menu, use 'UP' and 'DOWN' to select 'Account Settings.
A. Set phone number
Press 'SET/OK' to the submenu, use 'UP' and 'DOWN' to select 'Phone Number'.
Press 'SET/OK', and then, use 0~9 to input the phone number
B. Set user ID
Press 'SET/OK' to the submenu, use 'UP' and 'DOWN' to select 'User Identity'.
Press 'SET/OK', and then, use 0~9 to input the user ID. Continuous press a number key to change the letter and press '#' key to confirm it.
C. Set user password
Press 'SET/OK' to the submenu, use 'UP' and 'DOWN' to select 'User Password'.
Press 'SET/OK', and then, use 0~9 to input the user password. Continuous press a number key to change the letter and press '#' key to confirm it.
|
|
| Character Strings |
Corresponding Keys:
Key |
Characters |
1 |
. ,' ? ! " 1 - |
2 |
a b c 2 A B C 2 |
3 |
d e f 3 D E F 3 |
4 |
g h i 4 G H I 4 |
5 |
j k l 4 J K L 5 |
6 |
m n o 6 M N O 6 |
7 |
p q r s 7 P Q R S 7 |
8 |
t u v 8 T U V 8 |
9 |
w x y z 9 W X Y Z 9 |
0 |
( ) @ 0 - * & |
* |
* |
'*' can be used as radix point if only numbers are to be input.
If you need to enter a character, using the keys to enter the character you want. Press the same key repeatedly will change the character. If you need to enter the same character consecutively, press '#' to confirmed the last entry, then press again to enter the next entry.
Example: To enter 'aJtU', press '2555558#88888#' |
| |
|
|
|
|
|
|
|
|
